ExamPass EngineeringExamPass Engineering Start free
FE Electrical and Computer · Knowledge area 5 of 17

Electronics on the FE Electrical and Computer exam

Electronics accounts for 8 of the 110 questions — 7.3% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions8
Share of exam7.3%
Rank by weight5/17
In our bank26

What Electronics covers

On the FE Electrical and Computer exam this area covers diodes and rectifiers, bipolar and field-effect transistors, biasing, small-signal models, amplifiers, operational amplifiers, and power electronics.

What the questions look like: An op-amp gain, a transistor operating point, or a rectifier output.

Worth knowing cold: The ideal op-amp rules solve most of the amplifier questions in a line or two. Know the standard configurations by sight.

3 free Electronics practice problems

These come from our FE Electrical and Computer bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A discrete common-emitter BJT amplifier circuit is biased with an unbypassed emitter degeneration resistor $R_E$ as illustrated in the schematic. The circuit and transistor parameters are: - Supply voltage: $V_{CC} = +15.0\text{ V}$ - Voltage divider resistors: $R_1 = 47.0\text{ k}\Omega, R_2 = 10.0\text{ k}\Omega$ - Collector resistor: $R_C = 3.30\text{ k}\Omega$ - Emitter resistor: $R_E = 1.00\text{ k}\Omega$ - AC load resistor: $R_L = 4.70\text{ k}\Omega$ - Transistor current gain: $\beta = 100$ - Base-emitter turn-on voltage: $V_{BE(on)} = 0.70\text{ V}$ - Thermal voltage: $V_T = 25.0\text{ mV}$ Accounting for emitter degeneration and the AC load $R_L$ (with coupling capacitors acting as short circuits at mid-band frequencies), what is the small-signal voltage gain $A_v = v_o / v_{in}$ in volts per volt?

  1. A-0.85 V/V
  2. B-1.91 V/Vcorrect
  3. C-3.30 V/V
  4. D-6.85 V/V
Show the solution

**Step 1: Calculate DC Quiescent Operating Point (I_C, I_B)** From the FE Reference Handbook (Electrical and Computer / Bipolar Junction Transistors): Find Thevenin equivalent of the base bias network: $$V_{BB} = V_{CC} \left(\frac{R_2}{R_1 + R_2}\right) = 15.0 \left(\frac{10}{47 + 10}\right) = 15.0 \left(\frac{10}{57}\right) = 2.6316\text{ V}$$ $$R_B = R_1 \parallel R_2 = \frac{47 \times 10}{57} = 8.2456\text{ k}\Omega$$ Base loop KVL: $$V_{BB} = I_B R_B + V_{BE} + I_E R_E = I_B R_B + V_{BE} + (\beta + 1) I_B R_E$$ $$I_B = \frac{V_{BB} - V_{BE}}{R_B + (\beta + 1) R_E} = \frac{2.6316 - 0.70}{8.2456 + (101)(1.00)} = \frac{1.9316\text{ V}}{109.2456\text{ k}\Omega} = 0.01768\text{ mA}$$ Collector quiescent current: $$I_C = \beta I_B = 100(0.01768\text{ mA}) = 1.768\text{ mA}$$ **Step 2: Determine Small-Signal Transconductance (g_m)** $$g_m = \frac{I_C}{V_T} = \frac{1.768\text{ mA}}{25.0\text{ mV}} = 70.72\text{ mA/V} = 0.07072\text{ A/V}$$ **Step 3: Determine AC Collector Load (r_L)** At signal frequencies, $C_2$ is a short circuit, placing $R_L$ in parallel with $R_C$: $$r_L = R_C \parallel R_L = \frac{3.30 \times 4.70}{3.30 + 4.70} = \frac{15.51}{8.00} = 1.9388\text{ k}\Omega = 1{,}938.8\ \Omega$$ **Step 4: Compute Voltage Gain with Unbypassed Emitter Degeneration** For a common-emitter amplifier with unbypassed emitter resistance $R_E$: $$A_v = - \frac{g_m \cdot r_L}{1 + g_m R_E}$$ $$A_v = - \frac{(0.07072\text{ A/V}) \times (1{,}938.8\ \Omega)}{1 + (0.07072\text{ A/V}) \times (1{,}000\ \Omega)}$$ $$A_v = - \frac{137.11}{1 + 70.72} = - \frac{137.11}{71.72} = -1.9118\text{ V/V} \approx -1.91\text{ V/V}$$ *(Note: Without emitter degeneration, the gain would be $-g_m r_L = -137\text{ V/V}$, but $R_E$ provides negative feedback stabilizing the gain to $\approx -r_L/R_E = -1.94\text{ V/V}$).* Conclusion: The voltage gain is **-1.91 V/V**. Distractor Analysis: - Option A: Uses R_E without small-signal r_L parallel combination. - Option B: Correct. Accounts for small-signal load r_L = R_C || R_L and emitter degeneration feedback (1 + g_m R_E). - Option C: Omits load resistance R_L, considering only collector resistor R_C. - Option D: Ignores emitter degeneration resistance R_E entirely.

Problem 2

The complementary push-pull power amplifier shown in the diagram is biased in Class AB operation: - Symmetrical dual power supplies: $V_{CC} = +24.0\text{ V}$, $V_{EE} = -24.0\text{ V}$ - Load resistance: $R_L = 8.00\ \Omega$ - Transistor collector-emitter saturation voltage: $V_{CE,sat} = 2.00\text{ V}$ Assuming sinusoidal excitation, what is the maximum unclipped signal power $P_{L,max}$ delivered to the load, and what is the maximum power dissipation $P_{D,max}$ experienced by either output transistor?

  1. A24.5 W (with max transistor dissipation P_D = 5.85 W)
  2. B30.3 W (with max transistor dissipation P_D = 7.30 W)correct
  3. C36.0 W (with max transistor dissipation P_D = 9.12 W)
  4. D42.0 W (with max transistor dissipation P_D = 11.45 W)
Show the solution

**Step 1: Calculate the Maximum Output Voltage Amplitude** From the FE Reference Handbook (Electronics / Power Amplifiers): The maximum peak output voltage swing before clipping is: $$V_{om} = V_{CC} - V_{CE,sat} = 24.0\text{ V} - 2.00\text{ V} = 22.0\text{ V}$$ **Step 2: Determine Maximum Signal Power Delivered to the Load** $$P_{L,max} = \frac{V_{om}^2}{2 R_L} = \frac{(22.0)^2}{2(8.00)} = \frac{484.0}{16.0} = 30.25\text{ W} \approx 30.3\text{ W}$$ **Step 3: Analyze Transistor Power Dissipation as a Function of Output Swing** The average DC power drawn from the dual supplies for peak output voltage $V_p$ is: $$P_{dc} = \frac{2}{\pi} \frac{V_{CC} V_p}{R_L}$$ Total average power dissipated in both transistors is $P_{2D} = P_{dc} - P_L = \frac{2 V_{CC} V_p}{\pi R_L} - \frac{V_p^2}{2 R_L}$. Differentiating with respect to $V_p$ to find the worst-case operating point: $$\frac{d P_{2D}}{d V_p} = \frac{2 V_{CC}}{\pi R_L} - \frac{V_p}{R_L} = 0 \implies V_p = \frac{2}{\pi} V_{CC} = \frac{2(24.0)}{\pi} = 15.28\text{ V}$$ Because $15.28\text{ V} < 22.0\text{ V}$, this peak dissipation condition occurs within the linear operating range. **Step 4: Compute Maximum Power Dissipation Per Transistor** $$P_{D,max} = \frac{V_{CC}^2}{\pi^2 R_L} = \frac{(24.0)^2}{\pi^2 (8.00)} = \frac{576.0}{78.9568} = 7.295\text{ W} \approx 7.30\text{ W}$$ Conclusion: Maximum load power is **30.3 W** with maximum transistor dissipation **7.30 W**. Distractor Analysis: - Option A: with max transistor dissipation P_D = 5.85 W - Option B: with max transistor dissipation P_D = 7.30 W (Correct) - Option C: with max transistor dissipation P_D = 9.12 W - Option D: with max transistor dissipation P_D = 11.45 W

Problem 3

An operational amplifier circuit is configured as an inverting weighted summing amplifier with feedback resistor $R_f = 60.0\text{ k}\Omega$ powered by $\pm 15.0\text{ V}$ rails (output saturation limits at $\pm 13.5\text{ V}$). Two signals are connected to the inverting input junction: - Input 1: $V_1 = +1.50\text{ V}$ DC through $R_1 = 20.0\text{ k}\Omega$ - Input 2: $V_2(t) = 0.50 \sin(\omega t)\text{ V}$ AC through $R_2 = 10.0\text{ k}\Omega$ Non-inverting input is grounded ($0\text{ V}$). What are the DC component $V_{o,dc}$ and the peak AC amplitude $\hat{V}_{o,ac}$ of the output voltage waveform $v_o(t)$?

  1. A-2.50 V (with peak AC amplitude 1.50 V)
  2. B-4.50 V (with peak AC amplitude 3.00 V and 6.00 V saturation headroom)correct
  3. C-6.00 V (with peak AC amplitude 4.50 V)
  4. D-3.00 V (with peak AC amplitude 2.00 V)
Show the solution

**Step 1: Calculate Channel Gains** From the FE Reference Handbook (Electronics / Operational Amplifiers / Inverting Summing Amplifier): $$v_o(t) = -\left[ \frac{R_f}{R_1} V_1 + \frac{R_f}{R_2} V_2(t) \right]$$ $$A_1 = -\frac{R_f}{R_1} = -\frac{60.0\text{ k}\Omega}{20.0\text{ k}\Omega} = -3.00$$ $$A_2 = -\frac{R_f}{R_2} = -\frac{60.0\text{ k}\Omega}{10.0\text{ k}\Omega} = -6.00$$ **Step 2: Superposition of DC and AC Components** - DC output component: $$V_{o,dc} = A_1 V_1 = -3.00 \times (+1.50\text{ V}) = -4.50\text{ V}$$ - AC output component: $$v_{o,ac}(t) = A_2 V_2(t) = -6.00 \times [0.50 \sin(\omega t)] = -3.00 \sin(\omega t)\text{ V}$$ Peak AC amplitude: $\hat{V}_{o,ac} = 3.00\text{ V}$. **Step 3: Verify Saturation Headroom** Total waveform: $v_o(t) = -4.50 - 3.00 \sin(\omega t)\text{ V}$. Output extremes: $$v_{o,max} = -4.50 + 3.00 = -1.50\text{ V}$$ $$v_{o,min} = -4.50 - 3.00 = -7.50\text{ V}$$ Since $-13.5\text{ V} < -7.50\text{ V} < -1.50\text{ V} < +13.5\text{ V}$, the op-amp operates strictly within its linear range with $|-13.5 - (-7.50)| = 6.00\text{ V}$ of negative rail headroom. Conclusion: The DC component is **$-4.50\text{ V}$** and the peak AC amplitude is **$3.00\text{ V}$**. Distractor Analysis: - Option A: with peak AC amplitude 1.50 V - Option B: with peak AC amplitude 3.00 V and 6.00 V saturation headroom (Correct) - Option C: with peak AC amplitude 4.50 V - Option D: with peak AC amplitude 2.00 V

Find out where you actually stand

A free 20-question diagnostic across every FE Electrical and Computer knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Electronics is where your time should go at all.

Start the free Electrical & Computer diagnostic

Retaking the FE Electrical and Computer exam?

Copy the scores from your NCEES diagnostic report and see whether Electronics is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Electrical and Computer knowledge areas