ExamPass EngineeringExamPass Engineering Start free
FE Mechanical · Knowledge area 4 of 14

Mechanical Design and Analysis on the FE Mechanical exam

Mechanical Design and Analysis accounts for 11 of the 110 questions — 10.0% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions11
Share of exam10.0%
Rank by weight4/14
In our bank38

What Mechanical Design and Analysis covers

On the FE Mechanical exam this area covers stress analysis of machine elements, failure theories, fatigue and endurance limits, shafts, keys and couplings, bearings, gears, springs, and fasteners and welds.

What the questions look like: A factor of safety from a failure theory, a fatigue life, or a gear or shaft sizing.

Worth knowing cold: Know which failure theory applies to ductile and to brittle materials. Choosing the wrong one gives a confidently wrong answer.

3 free Mechanical Design and Analysis practice problems

These come from our FE Mechanical bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A shaft rotating at 1200 rev/min transmits 25 kW of power. What torque does the shaft carry, in N-m? Enter a number only.

Show the solution

Power delivered by a rotating shaft is the product of torque and angular velocity, P = T omega, with omega in radians per second. Convert the speed: omega = 1200 (2*pi) / 60 = 1200 (0.10472) = 125.66 rad/s Solve for torque: T = P / omega = 25,000 W / 125.66 rad/s = 198.9 N-m A range of 197 to 201 N-m is accepted here rather than a tight 1% band, because pi and the rev/min-to-rad/s conversion factor get rounded differently depending on how many decimal places someone carries through the intermediate steps -- the physics is exact, but 2*pi/60 = 0.1047197... has no clean stopping point, so a reasonable amount of rounding drift between two equally correct solution paths is expected and should not be marked wrong. The general relationship worth keeping: for a fixed power, torque and rotational speed are inversely proportional, which is why a speed-reducing gearbox multiplies torque in the same ratio it divides speed.

Problem 2

An epicyclic (planetary) gear set consists of a central sun gear S ($N_s = 20\text{ teeth}$), three planet gears P, a carrier arm C, and an outer ring gear R with internal teeth ($N_r = 80\text{ teeth}$). The outer ring gear is held stationary ($\omega_r = 0\text{ rpm}$). An electric motor drives the sun gear clockwise at $\omega_s = +1800.0\text{ rpm}$. In accordance with epicyclic gear train kinematics from the NCEES FE Reference Handbook ($\frac{\omega_r - \omega_c}{\omega_s - \omega_c} = -\frac{N_s}{N_r}$), the rotational speed and direction of the carrier arm output ($\omega_c$, in rpm) and the overall gear reduction ratio ($\omega_s/\omega_c$) are:

  1. A225 rpm (CW), gear ratio = 8.0:1
  2. B360 rpm (CW), gear ratio = 5.0:1correct
  3. C450 rpm (CW), gear ratio = 4.0:1
  4. D600 rpm (CCW), gear ratio = 3.0:1
Show the solution

Step 1: Set up the fundamental epicyclic velocity ratio equation from the NCEES FE Reference Handbook: $$\frac{\omega_r - \omega_c}{\omega_s - \omega_c} = -\frac{N_s}{N_r}$$ Given $N_s = 20$ teeth, $N_r = 80$ teeth, and $\omega_r = 0$: $$-\frac{N_s}{N_r} = -\frac{20}{80} = -0.250$$ Step 2: Solve for carrier angular velocity ($\omega_c$): $$\frac{0 - \omega_c}{1800.0 - \omega_c} = -0.250$$ $$-\omega_c = -0.250 (1800.0 - \omega_c) = -450.0 + 0.250 \omega_c$$ $$\omega_c + 0.250 \omega_c = 450.0 \implies 1.250 \omega_c = 450.0$$ $$\omega_c = \frac{450.0}{1.250} = +360.0\text{ rpm}$$ The positive sign confirms clockwise (CW) rotation, matching the sun gear direction. Step 3: Calculate the overall reduction ratio: $$\text{Gear Ratio} = \frac{\omega_s}{\omega_c} = \frac{1800.0\text{ rpm}}{360.0\text{ rpm}} = 5.00 = 5.0:1$$ Distractor Analysis: - Option A: Uses $N_r / N_s = 4.0$ squared as ratio. - Option B: Correct. - Option C: Neglects the carrier term in the denominator ($1800 / 4 = 450$). - Option D: Inverts the sign assuming internal ring meshing reverses carrier direction.

Problem 3

Rolling element bearings are engineered with distinct roller geometries to accommodate specific operational combinations of radial and axial thrust loads. Match each standard bearing type to its primary load carrying capability.

Show the solution

Step 1: Match bearing geometries with functional characteristics from the NCEES FE Reference Handbook (Mechanical Design): - Deep Groove Ball: Moderate bidirectional thrust + radial. - Cylindrical Roller: Highest radial capacity, zero thrust. - Tapered Roller: Heavy combined radial and unidirectional thrust. - Spherical Roller: Self-aligning with heavy radial load capacity. Step 2: Assign each bearing type to its matching description.

Find out where you actually stand

A free 20-question diagnostic across every FE Mechanical knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Mechanical Design and Analysis is where your time should go at all.

Start the free Mechanical diagnostic

Retaking the FE Mechanical exam?

Copy the scores from your NCEES diagnostic report and see whether Mechanical Design and Analysis is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Mechanical knowledge areas