ExamPass EngineeringExamPass Engineering Start free
FE Mechanical · Knowledge area 6 of 14

Mechanics of Materials on the FE Mechanical exam

Mechanics of Materials accounts for 10 of the 110 questions — 9.1% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions10
Share of exam9.1%
Rank by weight6/14
In our bank34

What Mechanics of Materials covers

On the FE Mechanical exam this area covers axial stress and strain, thermal deformation, torsion, shear and moment diagrams, bending and shear stress, combined loading, Mohr’s circle, and column buckling.

What the questions look like: A stress or elongation from a load, a shaft under torque, a maximum bending stress from a section modulus, or an Euler buckling load.

Worth knowing cold: Sign conventions for shear and moment diagrams cost more marks than any formula in this area. Fix them early and they stay fixed.

3 free Mechanics of Materials practice problems

These come from our FE Mechanical bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A solid circular rod 25 mm in diameter carries an axial compressive load of 40 kN. What is the normal stress in the rod, in MPa? Enter a number only.

Show the solution

For a prismatic bar under uniform axial load, normal stress is simply force over cross-sectional area. Area of the circular cross-section: A = pi d^2 / 4 = pi (0.025)^2 / 4 = pi (6.25e-4) / 4 = 4.909e-4 m^2 Stress: sigma = P / A = 40,000 N / 4.909e-4 m^2 = 8.149e7 Pa = 81.5 MPa The load is compressive, so technically this stress is negative by the usual tension-positive sign convention, but the question asks only for the magnitude in MPa, which is what gets entered. 81.5 MPa is comfortably below the yield strength of ordinary structural steel (roughly 250 MPa) or even mild aluminum alloys, so treating the rod as remaining elastic under this load is reasonable -- worth a glance whenever a problem gives you a resulting stress, since a number that turns out to exceed a typical yield strength is a signal to double check the arithmetic before moving on.

Problem 2

A thin-walled cylindrical pressure vessel has an internal gage pressure $P = 2.50\text{ MPa}$, an inside mean radius $r = 400.0\text{ mm}$, and a wall thickness $t = 8.00\text{ mm}$. In accordance with thin-walled pressure vessel equations and Mohr's circle from the NCEES FE Reference Handbook ($\sigma_h = P r / t$, $\sigma_l = P r / (2t)$, $\tau_{max,in-plane} = \frac{\sigma_h - \sigma_l}{2}$), calculate the maximum in-plane shear stress $\tau_{max}$ in megapascals (MPa). (Enter numerical value in MPa).

Show the solution

Step 1: Calculate the circumferential (hoop) stress ($\sigma_h$): $$\sigma_h = \frac{P r}{t} = \frac{(2.50\text{ MPa}) \times (400.0\text{ mm})}{8.00\text{ mm}} = \frac{1000.0}{8.00} = 125.0\text{ MPa}$$ Step 2: Calculate the longitudinal stress ($\sigma_l$): $$\sigma_l = \frac{P r}{2t} = \frac{\sigma_h}{2} = \frac{125.0\text{ MPa}}{2} = 62.50\text{ MPa}$$ Step 3: Compute the maximum in-plane shear stress ($\tau_{max,in-plane}$): $$\tau_{max,in-plane} = \frac{\sigma_h - \sigma_l}{2} = \frac{125.0\text{ MPa} - 62.50\text{ MPa}}{2} = \frac{62.50\text{ MPa}}{2} = 31.25\text{ MPa} = 31.3\text{ MPa}$$ (Note: Absolute maximum shear stress is $\tau_{abs} = \sigma_h / 2 = 62.5\text{ MPa}$, whereas in-plane shear stress is $31.25\text{ MPa}$). Distractor Analysis: - An answer of 62.5 MPa is the absolute out-of-plane maximum shear stress or longitudinal stress. - An answer of 125.0 MPa is the hoop stress.

Problem 3

A hollow thin-walled structural steel tube with rectangular cross-section has mean centerline dimensions $a = 120.0\text{ mm} = 0.120\text{ m}$ (width) and $b = 80.0\text{ mm} = 0.080\text{ m}$ (height), with uniform wall thickness $t = 4.00\text{ mm} = 0.00400\text{ m}$. Length of the tube is $L = 2.50\text{ m}$, and shear modulus is $G = 78.0\text{ GPa} = 78.0 \times 10^9\text{ Pa}$. A torque $T = 3.20\text{ kN}\cdot\text{m} = 3200.0\text{ N}\cdot\text{m}$ is applied. In accordance with the Bredt-Batho equations for thin-walled closed tubes from the NCEES FE Reference Handbook ($A_m = a b$, $\tau = \frac{T}{2 A_m t}$, $\phi = \frac{T L p_m}{4 A_m^2 G t}$), the maximum shear stress ($\tau$, in MPa) and total angle of twist ($\phi$, in degrees) are:

  1. A28.5 MPa, phi = 0.95°
  2. B41.7 MPa, phi = 1.59°correct
  3. C58.2 MPa, phi = 2.45°
  4. D75.0 MPa, phi = 3.10°
Show the solution

Step 1: Calculate the mean enclosed cross-sectional area ($A_m$) and perimeter ($p_m$): $$A_m = a \times b = (0.120\text{ m}) \times (0.080\text{ m}) = 0.00960\text{ m}^2 = 9.60 \times 10^{-3}\text{ m}^2$$ $$p_m = 2(a + b) = 2(0.120\text{ m} + 0.080\text{ m}) = 0.400\text{ m}$$ Step 2: Determine the uniform torsional shear stress ($\tau$): $$\tau = \frac{T}{2 A_m t} = \frac{3200.0\text{ N}\cdot\text{m}}{2 (0.00960\text{ m}^2)(0.00400\text{ m})} = \frac{3200.0}{7.680 \times 10^{-5}} = 41.6667 \times 10^6\text{ Pa} = 41.67\text{ MPa} = 41.7\text{ MPa}$$ Step 3: Calculate the total angle of twist ($\phi$): $$\phi = \frac{T L p_m}{4 A_m^2 G t} = \frac{(3200.0\text{ N}\cdot\text{m})(2.50\text{ m})(0.400\text{ m})}{4 (0.00960\text{ m}^2)^2 (78.0 \times 10^9\text{ Pa})(0.00400\text{ m})}$$ $$\phi = \frac{3200.0}{4 (9.216 \times 10^{-5})(3.120 \times 10^8)} = \frac{3200.0}{115,031} = 0.027818\text{ radians}$$ $$\phi = 0.027818\text{ rad} \times \left( \frac{180^\circ}{\pi} \right) = 1.5939^\circ = 1.59^\circ$$ Distractor Analysis: - Option A: Uses outer dimensions rather than mean centerline dimensions. - Option B: Correct. - Option C: Uses open thin-walled torsion formula $J = \frac{1}{3} p t^3$. - Option D: Omits the factor of 2 in Bredt-Batho denominator.

Find out where you actually stand

A free 20-question diagnostic across every FE Mechanical knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Mechanics of Materials is where your time should go at all.

Start the free Mechanical diagnostic

Retaking the FE Mechanical exam?

Copy the scores from your NCEES diagnostic report and see whether Mechanics of Materials is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Mechanical knowledge areas

Mechanics of Materials on other FE exams

The same knowledge area is weighted differently on each exam, and the questions differ with it.