ExamPass EngineeringExamPass Engineering Start free
FE Mechanical · Knowledge area 8 of 14

Heat Transfer on the FE Mechanical exam

Heat Transfer accounts for 8 of the 110 questions — 7.3% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions8
Share of exam7.3%
Rank by weight8/14
In our bank28

What Heat Transfer covers

On the FE Mechanical exam this area covers steady and transient conduction, thermal resistance networks, fins, free and forced convection, heat exchangers and LMTD, and radiation between surfaces.

What the questions look like: A heat rate through a composite wall, an exchanger area from the LMTD method, or an overall heat transfer coefficient.

Worth knowing cold: Thermal resistances in series and parallel behave exactly like electrical ones. Drawing the network makes composite-wall problems almost mechanical.

3 free Heat Transfer practice problems

These come from our FE Mechanical bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A plane wall 0.15 m thick, with thermal conductivity 0.50 W/m-K, has a surface area of 8.0 m^2. The temperature difference across it is 35 degrees C. What is the steady-state heat transfer rate, in kW? Enter a number only.

Show the solution

Steady one-dimensional conduction through a plane wall follows Fourier law in its integrated form: Q = k A (delta T) / L Substitute: Q = (0.50 W/m-K)(8.0 m^2)(35 K) / (0.15 m) Q = 140 / 0.15 = 933.3 W = 0.9333 kW The temperature difference can be left in degrees Celsius here because only a DIFFERENCE appears in the formula, and a one-degree interval is identical in size on the Celsius and Kelvin scales -- converting to absolute temperature would only matter for a calculation involving T raised to a power, such as radiation. The question asks for the answer in kW specifically, which is the detail most likely to trip someone who correctly computes 933 W and then enters that number instead of 0.933 -- reading what unit the question actually wants, not just getting the physics right, is itself part of what a fill-in format tests that multiple choice does not, since there is no list of four options to notice the mismatch against.

Problem 2

A solid spherical chrome steel ball bearing of diameter $D = 24.0\text{ mm} = 0.0240\text{ m}$ (radius $r_0 = 0.0120\text{ m}$, density $\rho = 7850.0\text{ kg/m}^3$, specific heat $c_p = 480.0\text{ J}/(\text{kg}\cdot\text{K})$, thermal conductivity $k = 50.0\text{ W}/(\text{m}\cdot\text{K})$) is initially at a uniform temperature $T_0 = 450.0^\circ\text{C}$. The ball is quenched in an air blast at $T_\infty = 25.0^\circ\text{C}$ with convective heat transfer coefficient $h = 75.0\text{ W}/(\text{m}^2\cdot\text{K})$. Characteristic length is $L_c = r_0 / 3 = 0.00400\text{ m}$, giving Biot number $Bi = \frac{h L_c}{k} = 0.0060 < 0.10$. In accordance with the lumped capacitance equations from the NCEES FE Reference Handbook ($\tau = \frac{\rho c_p L_c}{h}$, $\frac{T(t) - T_\infty}{T_0 - T_\infty} = e^{-t/\tau}$), the time required for the sphere center to cool to $T = 100.0^\circ\text{C}$ is most nearly:

  1. A215 s (3.58 min)
  2. B349 s (5.81 min)correct
  3. C480 s (8.00 min)
  4. D625 s (10.42 min)
Show the solution

Step 1: Calculate the thermal time constant ($\tau$) using the lumped capacitance model: $$L_c = \frac{V}{A_s} = \frac{\frac{4}{3}\pi r_0^3}{4\pi r_0^2} = \frac{r_0}{3} = \frac{0.0120\text{ m}}{3} = 0.00400\text{ m}$$ $$\tau = \frac{\rho c_p L_c}{h} = \frac{(7850.0\text{ kg/m}^3) \times (480.0\text{ J}/(\text{kg}\cdot\text{K})) \times (0.00400\text{ m})}{75.0\text{ W}/(\text{m}^2\cdot\text{K})}$$ $$\tau = \frac{15,072.0}{75.0} = 200.96\text{ seconds}$$ Step 2: Relate the dimensionless temperature fraction to elapsed cooling time: $$\frac{T(t) - T_\infty}{T_0 - T_\infty} = \frac{100.0^\circ\text{C} - 25.0^\circ\text{C}}{450.0^\circ\text{C} - 25.0^\circ\text{C}} = \frac{75.0}{425.0} = 0.176471$$ $$\frac{t}{\tau} = -\ln(0.176471) = -(-1.73460) = 1.73460$$ Step 3: Solve for cooling time ($t$): $$t = (200.96\text{ s}) \times (1.73460) = 348.58\text{ seconds} = 349\text{ s} = 5.81\text{ min}$$ Distractor Analysis: - Option A: Uses cylinder geometry $L_c = r_0 / 2$ instead of sphere $r_0 / 3$. - Option B: Correct. - Option C: Omits ambient temperature subtraction in ratio ($100 / 450 = 0.222$). - Option D: Uses $L_c = r_0$ without surface-area-to-volume geometric division.

Problem 3

A straight rectangular cooling fin of width $w = 1.00\text{ m}$ (into page), thickness $t = 4.00\text{ mm} = 0.00400\text{ m}$, and length $L = 50.0\text{ mm} = 0.0500\text{ m}$ is attached to a plane wall at base temperature $T_b = 120.0^\circ\text{C}$. The fin has thermal conductivity $k = 180.0\text{ W}/(\text{m}\cdot\text{K})$ and dissipates heat to surrounding air at $T_\infty = 20.0^\circ\text{C}$ with convective coefficient $h = 45.0\text{ W}/(\text{m}^2\cdot\text{K})$. Perimeter is $P \approx 2 w = 2.00\text{ m}$ and cross-section is $A_c = w t = 0.00400\text{ m}^2$ ($m = \sqrt{\frac{h P}{k A_c}} = 11.18\text{ m}^{-1}$). Using the corrected fin length for an adiabatic tip ($L_c = L + \frac{t}{2} = 0.0520\text{ m}$, $M = \sqrt{h P k A_c} \theta_b = 805.0\text{ W}$), calculate the fin heat dissipation rate ($q_{fin}$, in watts, W) in accordance with fin formulas from the NCEES FE Reference Handbook ($q_{fin} = M \tanh(m L_c)$). (Enter numerical value in watts).

Show the solution

Step 1: Calculate the fin parameter ($m$): $$m = \sqrt{\frac{h P}{k A_c}} = \sqrt{\frac{(45.0\text{ W}/(\text{m}^2\cdot\text{K}))(2.00\text{ m})}{(180.0\text{ W}/(\text{m}\cdot\text{K}))(0.00400\text{ m}^2)}} = \sqrt{\frac{90.0}{0.720}} = \sqrt{125.0} = 11.1803\text{ m}^{-1}$$ Step 2: Calculate corrected length ($L_c$) and argument ($m L_c$): $$L_c = L + \frac{t}{2} = 0.0500\text{ m} + 0.00200\text{ m} = 0.0520\text{ m}$$ $$m L_c = (11.1803\text{ m}^{-1})(0.0520\text{ m}) = 0.581378$$ $$\tanh(m L_c) = \tanh(0.581378) = 0.523612$$ Step 3: Compute maximum base heat transfer rate factor ($M$) and actual fin heat rate ($q_{fin}$): $$\theta_b = T_b - T_\infty = 120.0^\circ\text{C} - 20.0^\circ\text{C} = 100.0^\circ\text{C}$$ $$M = \sqrt{h P k A_c} \theta_b = \sqrt{(45.0)(2.00)(180.0)(0.00400)} \times 100.0 = \sqrt{64.80} \times 100.0 = 8.04984 \times 100.0 = 804.98\text{ W}$$ $$q_{fin} = M \tanh(m L_c) = (804.98\text{ W}) \times (0.523612) = 421.50\text{ W} = 421.5\text{ W}$$ Distractor Analysis: - Omitting tip correction (using $L = 0.050\text{ m}$) yields $410.2\text{ W}$. - Using infinitely long fin assumption yields $q = M = 805.0\text{ W}$.

Find out where you actually stand

A free 20-question diagnostic across every FE Mechanical knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Heat Transfer is where your time should go at all.

Start the free Mechanical diagnostic

Retaking the FE Mechanical exam?

Copy the scores from your NCEES diagnostic report and see whether Heat Transfer is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Mechanical knowledge areas

Heat Transfer on other FE exams

The same knowledge area is weighted differently on each exam, and the questions differ with it.