ExamPass EngineeringExamPass Engineering Start free
FE Civil · Knowledge area 6 of 18

Mechanics of Materials on the FE Civil exam

Mechanics of Materials accounts for 8 of the 110 questions — 7.3% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions8
Share of exam7.3%
Rank by weight6/18
In our bank27

What Mechanics of Materials covers

On the FE Civil exam this area covers axial stress and strain, thermal deformation, torsion, shear and moment diagrams, bending and shear stress, combined loading, Mohr’s circle, and column buckling.

What the questions look like: A stress or elongation from a load, a shaft under torque, a maximum bending stress from a section modulus, or an Euler buckling load.

Worth knowing cold: Sign conventions for shear and moment diagrams cost more marks than any formula in this area. Fix them early and they stay fixed.

3 free Mechanics of Materials practice problems

These come from our FE Civil bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A rectangular column, 0.20 m by 0.30 m in cross-section, carries a compressive axial load of 150 kN applied with an eccentricity of 0.05 m along the 0.30 m dimension. What is the maximum compressive stress on the cross-section, and does any part of the section go into tension?

  1. A5.0 MPa maximum; no tension anywhere in the sectioncorrect
  2. B5.0 MPa maximum; the far edge goes into tension
  3. C2.5 MPa maximum; no tension anywhere in the section
  4. D7.5 MPa maximum; the far edge goes into tension
Show the solution

This is a combined axial-plus-bending stress problem, solved by superposing the uniform axial stress and the bending stress from the eccentric load. Section properties: A = 0.20(0.30) = 0.06 m^2, I = 0.20(0.30)^3/12 = 0.00045 m^4, c = 0.15 m. Axial stress: sigma_axial = P/A = 150,000/0.06 = 2.5 MPa. Bending stress from the eccentric load: sigma_bending = P*e*c/I = 150,000(0.05)(0.15)/0.00045 = 2.5 MPa. The maximum stress (compression side) is the sum: sigma_max = 2.5 + 2.5 = 5.0 MPa. The minimum stress (opposite side) is the difference: sigma_min = 2.5 - 2.5 ≈ 0 MPa. Because the eccentricity places the load exactly at the edge of the section's kern, the far side reaches essentially zero stress rather than going into tension — a useful check in foundation and column design where tension is often undesirable.

Problem 2

A structural member can be loaded in several distinct ways, each producing a characteristic stress distribution across its cross-section. Match each loading type to the distribution it produces.

Show the solution

Knowing where each loading puts its maximum stress is what tells an engineer where a member will actually fail and which section property controls it. AXIAL LOADING distributes stress uniformly, so only the area matters and the shape is irrelevant — which is why a tension member is sized on area alone. BENDING produces the linear distribution that gives the neutral axis its name, with the extremes carrying the most, and this is precisely why an I-beam concentrates material in its flanges: material near the neutral axis is nearly idle. TORSION of a circular shaft produces the analogous linear shear distribution radially, maximum at the surface, which is the reason hollow shafts are so efficient — removing the lightly stressed core costs little capacity and saves much weight. TRANSVERSE SHEAR is the one that surprises people, because its distribution is the inverse of bending's: shear stress vanishes at the free top and bottom surfaces and peaks at the neutral axis, which is why the web of an I-beam carries nearly all the shear while the flanges carry the moment. The two unused labels describe hydrostatic compression and a fatigue effect, neither of which is one of these four distributions.

Problem 3

A fabricated structural T-beam cross section is subjected to a vertical shear force of $V = 36.0\text{ kN}$, as illustrated in the figure. The top flange dimensions are $b_f = 160\text{ mm}$ by $t_f = 20\text{ mm}$, and the vertical web dimensions are $t_w = 20\text{ mm}$ by $h_w = 160\text{ mm}$ (total section height $H = 180\text{ mm}$). The neutral axis lies at $\bar{y} = 55.0\text{ mm}$ below the top surface, and the moment of inertia about the neutral axis is $I_{NA} = 1.989 \times 10^7\text{ mm}^4$. What is the maximum transverse shear stress $\tau_{max}$ developed in the cross section?

  1. A9.8 MPa
  2. B11.6 MPa
  3. C12.8 MPa
  4. D14.1 MPacorrect
Show the solution

Step 1: Identify the shear stress formula from the Mechanics of Materials section of the FE Reference Handbook: $$\tau = \dfrac{V Q}{I t}$$ Maximum shear stress $\tau_{max}$ occurs at the neutral axis (N.A.), where the first moment of area $Q$ is maximized, and where the section thickness is the web width $t = t_w = 20\text{ mm} = 0.020\text{ m}$. Step 2: Calculate the first moment of area $Q_{NA}$ about the neutral axis: Taking the area below the neutral axis: The neutral axis is $55.0\text{ mm}$ from the top surface. The portion of the web below the neutral axis has height: $$h_{bot} = H - \bar{y} = 180.0\text{ mm} - 55.0\text{ mm} = 125.0\text{ mm}$$ Width of this bottom web portion is $t_w = 20.0\text{ mm}$. $$A_{bot} = 125.0\text{ mm} \times 20.0\text{ mm} = 2,500\text{ mm}^2$$ The centroid of this area lies at distance $\bar{y}'$ from the neutral axis: $$\bar{y}' = \dfrac{125.0\text{ mm}}{2} = 62.5\text{ mm}$$ $$Q_{NA} = A_{bot} \times \bar{y}' = 2,500\text{ mm}^2 \times 62.5\text{ mm} = 156,250\text{ mm}^3 = 1.5625 \times 10^{-4}\text{ m}^3$$ Step 3: Convert section properties to consistent SI units: $$V = 36.0\text{ kN} = 36,000\text{ N}$$ $$I_{NA} = 1.98933 \times 10^7\text{ mm}^4 = 1.98933 \times 10^{-5}\text{ m}^4$$ $$t = t_w = 0.020\text{ m}$$ Step 4: Compute the maximum shear stress $\tau_{max}$: $$\tau_{max} = \dfrac{(36,000\text{ N})(1.5625 \times 10^{-4}\text{ m}^3)}{(1.98933 \times 10^{-5}\text{ m}^4)(0.020\text{ m})} = \dfrac{5.625}{3.97867 \times 10^{-7}} = 14.138 \times 10^6\text{ Pa} = 14.14\text{ MPa} \approx 14.1\text{ MPa}$$ Distractor Analysis: - Option A (9.8 MPa) evaluates $Q$ at the flange-web junction rather than at the neutral axis. - Option B (11.6 MPa) uses the flange width $b_f = 160\text{ mm}$ in the denominator thickness $t$. - Option C (12.8 MPa) computes $Q$ taking only the web portion below the N.A. with an erroneous lever arm.

Find out where you actually stand

A free 20-question diagnostic across every FE Civil knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Mechanics of Materials is where your time should go at all.

Start the free Civil diagnostic

Retaking the FE Civil exam?

Copy the scores from your NCEES diagnostic report and see whether Mechanics of Materials is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Civil knowledge areas

Mechanics of Materials on other FE exams

The same knowledge area is weighted differently on each exam, and the questions differ with it.