ExamPass EngineeringExamPass Engineering Start free
FE Civil · Knowledge area 2 of 18

Hydraulics and Hydrologic Systems on the FE Civil exam

Hydraulics and Hydrologic Systems accounts for 9 of the 110 questions — 8.2% of your exam. It is one of the three heaviest areas on this paper, so it is worth your study time before almost anything else.

Questions9
Share of exam8.2%
Rank by weight2/18
In our bank33

What Hydraulics and Hydrologic Systems covers

On the FE Civil exam this area covers closed-conduit and open-channel flow, pumps and pump curves, the hydrologic cycle, rainfall-runoff and the rational method, hydrographs, storm sewers, detention, and groundwater.

What the questions look like: A peak discharge from the rational method, a normal or critical depth, a pump operating point, or a head loss.

Worth knowing cold: Open-channel and closed-conduit problems use different tools. Identify which one you are in before reaching for Manning or Darcy-Weisbach.

3 free Hydraulics and Hydrologic Systems practice problems

These come from our FE Civil bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A circular storm sewer pipe, 0.6 m in diameter, flows full under gravity on a slope of 0.004 m/m, with Manning's n = 0.013. Using the Manning equation for a full circular pipe (R = D/4), what is the full-flow capacity, and is it adequate for a design discharge of 0.45 m^3/s?

  1. AQ ≈ 0.52 m^3/s, adequate
  2. BQ ≈ 0.39 m^3/s, not adequatecorrect
  3. CQ ≈ 0.52 m^3/s, not adequate
  4. DQ ≈ 0.65 m^3/s, adequate
Show the solution

For a circular pipe flowing full, the hydraulic radius simplifies to R = D/4 regardless of the pipe's actual diameter, which is the key fact that makes the full-pipe case easy to check with the ordinary Manning equation. Cross-sectional area: A = pi/4(0.6)^2 = 0.2827 m^2. Hydraulic radius: R = D/4 = 0.15 m. Manning velocity: V = (1/n)*R^(2/3)*S^(1/2) = (1/0.013)(0.15^(2/3))(0.004^0.5) = 1.373 m/s. Capacity: Q = V*A = 1.373*0.2827 = 0.388 m^3/s. Since the design discharge of 0.45 m^3/s exceeds this full-flow capacity of 0.388 m^3/s, the pipe is undersized and NOT adequate for this design flow.

Problem 2

Flow in a rectangular open channel is being classified as subcritical or supercritical. Which of the following observations indicate that the flow is SUPERCRITICAL? Select the two that apply.

  1. AThe Froude number is greater than one
  2. BThe Froude number is less than one
  3. CSurface disturbances are able to travel upstream against the flow
  4. DThe flow depth is less than the critical depth for that discharge
Show the solution

The Froude number compares the flow velocity against the speed at which a shallow-water surface wave travels, and that single comparison defines the flow regime and determines how the channel behaves. A FROUDE NUMBER GREATER THAN ONE means the water is moving faster than a disturbance can propagate, which is the definition of supercritical flow. A DEPTH LESS THAN CRITICAL is the same statement expressed geometrically: for a given discharge there is one critical depth, and flowing shallower than it means flowing faster than critical — the shallow, fast, rushing flow below a spillway. A FROUDE NUMBER LESS THAN ONE is subcritical, the deep, tranquil flow of most natural rivers. DISTURBANCES TRAVELLING UPSTREAM is also a subcritical signature, and it carries a practical consequence that matters more than the label: in subcritical flow a downstream control such as a weir or a culvert outlet influences depths upstream, so the water surface profile is computed in the upstream direction, whereas in supercritical flow the control is upstream and the computation proceeds downstream. Getting that direction wrong is the usual way a backwater analysis goes astray.

Problem 3

A symmetrical trapezoidal open irrigation canal has a bottom width of b = 4.00 m and side slopes of z = 1.50 (horizontal) to 1.0 (vertical). The canal conveys a steady design discharge of Q = 20.00 m³/s. According to open-channel hydraulic theory, critical flow occurs when the Froude number equals unity (Fr = 1), satisfying the governing section factor equation: Q² * T / (g * A³) = 1.00 ==> Q² / g = A³ / T where: - Flow cross-sectional area: A = (b + z * y) * y = (4.00 + 1.50 * y) * y - Top water surface width: T = b + 2 * z * y = 4.00 + 3.00 * y - Gravitational acceleration: g = 9.81 m/s² Refer to the accompanying technical diagram [FE-CIV-1753]. What is the critical flow depth yc (in meters) for this discharge?

  1. A0.85 m
  2. B1.52 m
  3. C1.34 m
  4. D1.17 mcorrect
Show the solution

Step 1 - Critical Flow Governing Relation: At critical flow conditions ($Fr = V / \sqrt{g D} = 1.0$ where hydraulic depth $D = A / T$): $$\frac{Q^2 \cdot T}{g \cdot A^3} = 1.00 \implies \frac{Q^2}{g} = \frac{A^3}{T}$$ Step 2 - Evaluate the Discharge Parameter ($Q^2 / g$): With $Q = 20.00\text{ m}^3\text{/s}$ and $g = 9.81\text{ m/s}^2$: $$\frac{Q^2}{g} = \frac{(20.00\text{ m}^3\text{/s})^2}{9.81\text{ m/s}^2} = \frac{400.00}{9.81} = 40.7747\text{ m}^5$$ Step 3 - Geometric Functions of Depth ($y$): - Area: $A(y) = (4.00 + 1.50 y) y$ - Top width: $T(y) = 4.00 + 3.00 y$ Step 4 - Numerical Root Finding for $y_c$: - Test Option A ($y = 0.85\text{ m}$): $$A = (4.00 + 1.275)(0.85) = 4.484\text{ m}^2, \quad T = 6.55\text{ m}$$ $$\frac{A^3}{T} = \frac{90.15}{6.55} = 13.76 \ll 40.77$$ - Test Option C ($y = 1.34\text{ m}$): $$A = (4.00 + 2.01)(1.34) = 8.053\text{ m}^2, \quad T = 8.02\text{ m}$$ $$\frac{A^3}{T} = \frac{522.3}{8.02} = 65.12 \gg 40.77$$ - Test Option D ($y = 1.173\text{ m}$): $$A = (4.00 + 1.50 \times 1.173)(1.173) = 6.756\text{ m}^2, \quad T = 4.00 + 3.519 = 7.519\text{ m}$$ $$\frac{A^3}{T} = \frac{(6.756)^3}{7.519} = \frac{308.35}{7.519} = 41.01 \approx 40.77$$ Step 5 - Distractor Analysis: - Option A ($0.85\text{ m}$) corresponds to a rectangular channel without side slopes ($y_c = (q^2/g)^{1/3} = 0.88\text{ m}$). - Option B ($1.52\text{ m}$) results from inverting the Froude ratio ($A/T^3$). - Option C ($1.34\text{ m}$) results from using $T = b + z y$ instead of $b + 2 z y$. Therefore, the critical depth is 1.17 m (Option D).

Find out where you actually stand

A free 20-question diagnostic across every FE Civil knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Hydraulics and Hydrologic Systems is where your time should go at all.

Start the free Civil diagnostic

Retaking the FE Civil exam?

Copy the scores from your NCEES diagnostic report and see whether Hydraulics and Hydrologic Systems is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Civil knowledge areas