ExamPass EngineeringExamPass Engineering Start free
FE Civil · Knowledge area 5 of 18

Statics on the FE Civil exam

Statics accounts for 8 of the 110 questions — 7.3% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions8
Share of exam7.3%
Rank by weight5/18
In our bank27

What Statics covers

On the FE Civil exam this area covers resultants of force systems, equilibrium of rigid bodies, trusses and frames, centroids and moments of inertia, and friction.

What the questions look like: A reaction at a support, a member force in a truss by joints or sections, a centroid of a composite area, or a block on the verge of sliding.

Worth knowing cold: Free-body diagrams are not optional. Drawing one properly turns most of these into two equations and a division.

3 free Statics practice problems

These come from our FE Civil bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A symmetric triangular truss spans 4 m with a 3 m rise (apex at (2, 3), supports at (0,0) and (4,0)), pinned at both supports. A 30 kN downward load is applied at the apex. Member AC (from the left support to the apex) has a cross-sectional area of 500 mm². If the allowable stress is 150 MPa, what is the stress in member AC, and does it pass?

  1. A18.0 MPa — passes
  2. B36.1 MPa — passescorrect
  3. C72.1 MPa — passes
  4. D180.3 MPa — fails
Show the solution

First find the reaction, then the member force by joint equilibrium, then convert to stress. By symmetry, each reaction carries half the load: R A = 30/2 = 15 kN. Member AC runs from (0,0) to (2,3), length = √(2²+3²) = √13 = 3.606 m. sinθ (vertical component fraction) = 3/3.606 = 0.8321. At joint A, vertical equilibrium: F AC sinθ = R A → F AC = 15/0.8321 = 18.03 kN (compression, pushing down and outward to balance the upward reaction). Stress = F AC /A = 18,030 N / 500 mm² = 36.06 MPa. Since 36.06 MPa < 150 MPa allowable, the member passes with a comfortable margin (factor of safety ≈ 4.16). Sanity check: a shallower truss (smaller rise-to-span ratio) would require a larger diagonal force for the same vertical reaction, since sinθ would shrink — this truss's fairly steep 3:2 rise-to-half-span geometry keeps the member force moderate relative to the applied load.

Problem 2

A 600 N lighting fixture hangs from ring C, supported by two cables. Cable AC goes up and to the left at 30° above the horizontal; cable BC goes up and to the right at 45° above the horizontal. The tension in cable BC is most nearly:

  1. A439 N
  2. B538 Ncorrect
  3. C600 N
  4. D849 N
Show the solution

Step 1: Free-body diagram of ring C, with $T_{AC}$ at 30° and $T_{BC}$ at 45° above the horizontal and the 600 N weight down. Step 2: Horizontal equilibrium: $$T_{BC}\cos 45^\circ = T_{AC}\cos 30^\circ \implies T_{BC} = T_{AC}\dfrac{0.8660}{0.7071} = 1.2247\,T_{AC}$$ Step 3: Vertical equilibrium: $$T_{AC}\sin 30^\circ + T_{BC}\sin 45^\circ = 600$$ $$T_{AC}(0.5) + 1.2247\,T_{AC}(0.7071) = 600 \implies 1.3660\,T_{AC} = 600$$ $$T_{AC} = 439.2\text{ N}$$ Step 4: $T_{BC} = 1.2247(439.2) = 537.9 \approx 538\text{ N}$. Distractor Analysis: - Option A (439) is the tension in cable AC. - Option C (600) assumes the steeper cable carries the full weight. - Option D (849) is $600/\sin 45^\circ$, ignoring cable AC.

Problem 3

A determinate structural beam $ABC$ consists of a main span $AB = 6.0\text{ m}$ and an overhang cantilever $BC = 2.0\text{ m}$, as shown in the figure. The beam is supported by a pin at $A$ and a roller at $B$. The main span $AB$ carries a linearly varying trapezoidal distributed load ranging from $w_1 = 12\text{ kN/m}$ at $A$ to $w_2 = 24\text{ kN/m}$ at $B$. A concentrated vertical load of $P = 30\text{ kN}$ acts downward at the free cantilever tip $C$. What is the vertical reaction force $R_B$ at roller support $B$?

  1. A78.0 kN
  2. B88.0 kN
  3. C100.0 kNcorrect
  4. D112.0 kN
Show the solution

Step 1: Decompose the trapezoidal distributed load on span $AB$ ($L_1 = 6.0\text{ m}$) into a uniform rectangular load and a triangular load: - Uniform rectangular load: $$w_{rect} = 12\text{ kN/m}$$ $$W_1 = w_{rect} \times L_1 = 12\text{ kN/m} \times 6.0\text{ m} = 72.0\text{ kN}$$ Centroid location from pin $A$: $\bar{x}_1 = \dfrac{6.0}{2} = 3.0\text{ m}$ - Triangular load: $$w_{tri} = w_2 - w_1 = 24 - 12 = 12\text{ kN/m}$$ $$W_2 = \dfrac{1}{2} \times w_{tri} \times L_1 = \dfrac{1}{2} \times 12 \times 6.0 = 36.0\text{ kN}$$ Centroid location from pin $A$: $\bar{x}_2 = \dfrac{2}{3}(6.0\text{ m}) = 4.0\text{ m}$ Step 2: Identify the moment arm for the concentrated load $P$ at cantilever tip $C$: Point $C$ is at distance $x_C = 6.0\text{ m} + 2.0\text{ m} = 8.0\text{ m}$ from pin $A$. Step 3: Sum moments about pin support $A$ (counterclockwise positive): $$\sum M_A = 0 \implies R_B(6.0\text{ m}) - W_1(\bar{x}_1) - W_2(\bar{x}_2) - P(x_C) = 0$$ $$6.0 R_B - (72.0\text{ kN})(3.0\text{ m}) - (36.0\text{ kN})(4.0\text{ m}) - (30.0\text{ kN})(8.0\text{ m}) = 0$$ $$6.0 R_B - 216.0 - 144.0 - 240.0 = 0$$ $$6.0 R_B - 600.0 = 0$$ $$R_B = \dfrac{600.0}{6.0} = 100.0\text{ kN} \uparrow$$ Distractor Analysis: - Option A (78.0 kN) incorrectly calculates the triangular load centroid as $1/3$ from $A$ ($2.0\text{ m}$) instead of $2/3$ from $A$ ($4.0\text{ m}$). - Option B (88.0 kN) neglects the overhang load $P = 30\text{ kN}$ on the moment balance. - Option D (112.0 kN) treats the entire distributed load as an equivalent uniform load of $24\text{ kN/m}$.

Find out where you actually stand

A free 20-question diagnostic across every FE Civil knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Statics is where your time should go at all.

Start the free Civil diagnostic

Retaking the FE Civil exam?

Copy the scores from your NCEES diagnostic report and see whether Statics is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Civil knowledge areas

Statics on other FE exams

The same knowledge area is weighted differently on each exam, and the questions differ with it.