ExamPass EngineeringExamPass Engineering Start free
FE Civil · Knowledge area 7 of 18

Structural Analysis on the FE Civil exam

Structural Analysis accounts for 7 of the 110 questions — 6.4% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions7
Share of exam6.4%
Rank by weight7/18
In our bank25

What Structural Analysis covers

On the FE Civil exam this area covers determinacy and stability, analysis of beams, trusses and frames, influence lines, deflections by energy and geometric methods, and an introduction to indeterminate structures.

What the questions look like: A reaction, a member force, a maximum moment, or a deflection at a point.

Worth knowing cold: Check determinacy first. Attempting an indeterminate structure with statics alone wastes minutes you cannot get back.

3 free Structural Analysis practice problems

These come from our FE Civil bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

The symmetric triangular truss shown has a base of 8 m, an apex height of 3 m, and carries a 50 kN downward load at the apex. Each support reaction is 25 kN. Using the method of joints, that diagonal member carries an axial stress of 52.1 MPa over a cross-sectional area of 800 mm^2. What is the axial force in the diagonal member, and is it tension or compression?

  1. A41.7 kN, compressioncorrect
  2. B25.0 kN, compression
  3. C41.7 kN, tension
  4. D50.0 kN, compression
Show the solution

Work backward from the given stress to recover the member force, then confirm it independently from equilibrium at the support joint. From stress: F = stress*A = 52.1 MPa * 800 mm^2 = 41,680 N ≈ 41.7 kN. Independently, by the method of joints: the half-base is 4 m and the diagonal length is sqrt(4^2+3^2) = 5 m, so sin(theta) = 3/5 = 0.6 for the angle the diagonal makes with the horizontal. At the support joint, vertical equilibrium requires the diagonal's vertical component to balance the 25 kN reaction: Fdiag*sin(theta) = 25 kN, so Fdiag = 25/0.6 = 41.67 kN, matching the stress-based value. The diagonal pushes down and outward into the support under the apex load, which is the signature of a member in compression, not tension.

Problem 2

The single-bay portal frame shown has fixed bases at A and D, a height of 5 m, and a span of 8 m. A lateral load H = 30 kN is applied at joint B. Using the portal method, which assumes the lateral load splits equally between the two columns, what is the bending moment at the fixed base A?

  1. A37.5 kN·m, obtained by applying the column's shear to half the column height
  2. B150 kN·m, obtained by applying the full lateral load to a single column instead of splitting it
  3. C75 kN·mcorrect
  4. D24 kN·m, obtained by multiplying the shear per column by the span instead of the height
Show the solution

The portal method is an approximate but standard technique for quickly estimating moments in a low-rise frame under lateral load: it assumes the two columns of a single-bay frame are equally stiff and therefore share the story shear equally, which converts an indeterminate frame problem into something solvable by statics alone. Shear carried by each column: $\dfrac{H}{2} = \dfrac{30}{2} = 15$ kN. Each column behaves like a cantilever fixed at its base, so the base moment is that column's shear times the full column height (the shear is constant along the column's height in this idealization, with no intermediate load applied along its length): $M_A = 15(5) = 75$ kN·m. This base moment is what governs the required column reinforcement or connection design at the foundation, and by symmetry the same 75 kN·m develops at the base of column D — a useful check, since any asymmetry in the computed base moments would signal an arithmetic error rather than a real structural effect, given the frame's symmetric geometry and equal column stiffness assumption.

Problem 3

A symmetrical Pratt bridge truss has a span of $12.0\text{ m}$ consisting of four equal panels of length $d = 3.0\text{ m}$ and a height $h = 4.0\text{ m}$. The truss is pinned at support $A$ and supported by a roller at support $E$. A single concentrated gravity load $P = 80.0\text{ kN}$ acts downward at midspan joint $C$. Neglecting the self-weight of the truss members, using the method of sections (cutting section $a-a$ through members $FG$, $FC$, and $BC$), the internal axial force in the top chord member $FG$ is most nearly:

  1. A40.0 kN (tension)
  2. B50.0 kN (compression)
  3. C60.0 kN (compression)correct
  4. D80.0 kN (compression)
Show the solution

Step 1: Determine the external reactions at supports $A$ and $E$: - Total span: $L = 4 \times 3.0\text{ m} = 12.0\text{ m}$. - Concentrated vertical load $P = 80.0\text{ kN}$ is applied at the center of the span (joint $C$, $x = 6.0\text{ m}$). - Due to structural and loading symmetry: $$R_A = R_E = \dfrac{P}{2} = \dfrac{80.0\text{ kN}}{2} = 40.0\text{ kN} \quad (\text{upward})$$ Horizontal reaction at pinned support $A$: $R_{Ax} = 0$. Step 2: Pass cutting section $a-a$ through members $FG$, $FC$, and $BC$: - Consider the free-body diagram of the left portion of the truss (containing joints $A$, $B$, and $F$). - The exposed internal forces at the cut are $F_{FG}$ (top chord, horizontal at $y = 4.0\text{ m}$), $F_{FC}$ (diagonal), and $F_{BC}$ (bottom chord, horizontal at $y = 0$). Step 3: Apply moment equilibrium about joint $C$ ($x = 6.0\text{ m}, y = 0$): Joint $C$ is chosen because both $F_{FC}$ and $F_{BC}$ pass directly through $C$, eliminating them from the moment equation: $$\sum M_C = 0 \implies (R_A \times 6.0\text{ m}) - (F_{FG} \times 4.0\text{ m}) = 0$$ $$\left(40.0\text{ kN} \times 6.0\text{ m}\right) - \left(F_{FG} \times 4.0\text{ m}\right) = 0$$ $$240.0\text{ kN}\cdot\text{m} - 4.0 F_{FG} = 0$$ $$F_{FG} = \dfrac{240.0\text{ kN}\cdot\text{m}}{4.0\text{ m}} = 60.0\text{ kN}$$ Step 4: Determine member force sense (tension or compression): - In a simply supported truss subjected to downward gravity loads, the top chord is in compression, pushing into the joint. - A positive value confirms that member $FG$ is in compression ($60.0\text{ kN C}$). Distractor Analysis: - Option A (40.0 kN tension) confuses the member force with the external support reaction $R_A$ and reverses the sense. - Option B (50.0 kN compression) calculates the axial force in the diagonal member $F_{FC}$ ($F_{FC} = 40.0 \times 5/4 = 50.0\text{ kN T}$). - Option C (60.0 kN compression) is the exact force in member $FG$. - Option D (80.0 kN compression) assumes the full applied load $P$ is transferred directly into the top chord.

Find out where you actually stand

A free 20-question diagnostic across every FE Civil knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Structural Analysis is where your time should go at all.

Start the free Civil diagnostic

Retaking the FE Civil exam?

Copy the scores from your NCEES diagnostic report and see whether Structural Analysis is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Civil knowledge areas