ExamPass EngineeringExamPass Engineering Start free
FE Chemical · Knowledge area 15 of 17

Materials Science on the FE Chemical exam

Materials Science accounts for 4 of the 110 questions — 3.6% of your exam. It is one of the lighter areas, which makes it a good place to secure quick marks rather than a place to spend weeks.

Questions4
Share of exam3.6%
Rank by weight15/17
In our bank15

What Materials Science covers

On the FE Chemical exam this area covers atomic bonding and crystal structure, phase diagrams, heat treatment, mechanical properties and testing, corrosion, and polymers, ceramics and composites.

What the questions look like: Reading a phase diagram, relating a processing step to a property, or identifying a failure mechanism.

Worth knowing cold: Phase diagram questions are the most common and the most learnable. Practise the lever rule until it is automatic.

3 free Materials Science practice problems

These come from our FE Chemical bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A 316L stainless steel agitator shaft operating in a chemical reaction medium containing chloride ions undergoes uniform electrochemical corrosion. An electrochemical polarization test gives a measured corrosion current density of $i_{corr} = 15.0\text{ }\mu\text{A/cm}^2$. The alloy has an equivalent weight of $EW = 25.5\text{ g/equivalent}$ and a density of $\rho = 8.00\text{ g/cm}^3$. Using Faraday's law of electrolysis as formulated in the FE Reference Handbook, the Corrosion Penetration Rate (CPR) in millimeters per year is most nearly:

  1. A0.085 mm/yr
  2. B0.156 mm/yrcorrect
  3. C0.245 mm/yr
  4. D0.382 mm/yr
Show the solution

Step 1: Identify the Corrosion Penetration Rate (CPR) equation from the FE Reference Handbook: $$CPR = K \dfrac{i_{corr} \cdot EW}{\rho}$$ where the metric conversion constant is $K = 0.00327\text{ mm}\cdot\text{g}/(\mu\text{A}\cdot\text{cm}\cdot\text{yr})$ when $i_{corr}$ is in $\mu\text{A/cm}^2$, $EW$ is in g/equiv, and $\rho$ is in $\text{g/cm}^3$. Step 2: Substitute the known values: $$i_{corr} = 15.0\text{ }\mu\text{A/cm}^2$$ $$EW = 25.5\text{ g/equivalent}$$ $$\rho = 8.00\text{ g/cm}^3$$ Step 3: Calculate the corrosion rate: $$CPR = 0.00327 \times \dfrac{15.0 \times 25.5}{8.00} = 0.00327 \times \dfrac{382.5}{8.00} = 0.00327 \times 47.8125$$ $$CPR = 0.15635\text{ mm/year} \approx 0.156\text{ mm/yr}$$ Step 4: Engineering significance: With an annual loss of $0.156\text{ mm/yr}$, a standard corrosion allowance of $2.0\text{ mm}$ will protect the equipment for $2.0 / 0.156 = 12.8\text{ years}$. Distractor Analysis: - Option A (0.085 mm/yr) uses the molar mass of iron ($55.85$) instead of the equivalent weight divided by valence. - Option C (0.245 mm/yr) uses density of titanium or aluminum instead of steel ($8.0\text{ g/cm}^3$). - Option D (0.382 mm/yr) forgets the conversion factor $K$ or divides incorrectly by $\rho$.

Problem 2

A pressure vessel fabricated from high-strength low-alloy steel contains an internal through-thickness crack of length $2a = 10.0\text{ mm}$ ($a = 5.00\text{ mm} = 0.0050\text{ m}$). The plane strain fracture toughness of the alloy is $K_{Ic} = 55.0\text{ MPa}\cdot\text{m}^{1/2}$. Assuming a geometric shape factor of $Y = 1.00$, the critical applied tensile stress ($\sigma_c$, in MPa) that will cause catastrophic brittle fracture is most nearly:

  1. A220 MPa
  2. B310 MPa
  3. C439 MPacorrect
  4. D620 MPa
Show the solution

Step 1: State the linear elastic fracture mechanics (LEFM) equation for critical stress intensity from the NCEES FE Reference Handbook: $$K_{Ic} = Y \sigma_c \sqrt{\pi a}$$ where $K_{Ic}$ is plane strain fracture toughness, $Y$ is dimensionless geometry factor, $\sigma_c$ is nominal tensile stress, and $a$ is half-crack length. Step 2: Rearrange to solve for critical stress ($\sigma_c$): $$\sigma_c = \frac{K_{Ic}}{Y \sqrt{\pi a}}$$ Step 3: Substitute parameters in consistent SI units: $$K_{Ic} = 55.0\text{ MPa}\cdot\text{m}^{1/2}$$ $$Y = 1.00$$ $$a = 0.0050\text{ m}$$ $$\sqrt{\pi a} = \sqrt{\pi \times 0.0050\text{ m}} = \sqrt{0.015708\text{ m}} \approx 0.12533\text{ m}^{1/2}$$ Step 4: Compute the critical tensile stress ($\sigma_c$): $$\sigma_c = \frac{55.0\text{ MPa}\cdot\text{m}^{1/2}}{1.00 \times 0.12533\text{ m}^{1/2}} \approx 438.84\text{ MPa} \approx 439\text{ MPa}$$ Distractor Analysis: - Option A (220 MPa): Uses full crack length $2a = 0.010\text{ m}$ in the square root: $55.0 / \sqrt{\pi \times 0.010} = 310$ with arithmetic error. - Option B (310 MPa): Uses $2a = 0.010\text{ m}$ instead of half-crack $a = 0.0050\text{ m}$. - Option C (439 MPa): Correct. - Option D (620 MPa): Omits $\pi$ inside the square root.

Problem 3

A pure palladium foil membrane of thickness $L = 50.0\ \mu\text{m} = 5.00 \times 10^{-5}\text{ m}$ is used for hydrogen gas purification. The permeability coefficient of hydrogen in the palladium matrix is $P_m = 1.50 \times 10^{-8}\text{ mol}/(\text{m}\cdot\text{s}\cdot\text{Pa}^{0.5})$. The hydrogen partial pressure on the retentate (high-pressure) side is $p_h = 4.00 \times 10^6\text{ Pa}$, and on the permeate (low-pressure) side is $p_l = 2.50 \times 10^5\text{ Pa}$. In accordance with Sieverts' law for interstitial dissociative gas permeation ($J = \frac{P_m}{L} (p_h^{0.5} - p_l^{0.5})$), calculate the steady-state hydrogen flux $J$ in $\text{mol}/(\text{m}^2\cdot\text{s})$. (Enter numerical value).

Show the solution

Step 1: Evaluate the square roots of the upstream and downstream hydrogen partial pressures: $$\sqrt{p_h} = \sqrt{4.00 \times 10^6\text{ Pa}} = 2000.0\text{ Pa}^{0.5}$$ $$\sqrt{p_l} = \sqrt{2.50 \times 10^5\text{ Pa}} = 500.0\text{ Pa}^{0.5}$$ $$\Delta (p^{0.5}) = p_h^{0.5} - p_l^{0.5} = 2000.0 - 500.0 = 1500.0\text{ Pa}^{0.5}$$ Step 2: Calculate the steady-state permeation flux ($J$): $$J = \frac{P_m}{L} (p_h^{0.5} - p_l^{0.5}) = \frac{1.50 \times 10^{-8}\text{ mol}/(\text{m}\cdot\text{s}\cdot\text{Pa}^{0.5})}{5.00 \times 10^{-5}\text{ m}} \times (1500.0\text{ Pa}^{0.5})$$ $$J = (3.00 \times 10^{-4}) \times 1500.0 = 0.450\text{ mol}/(\text{m}^2\cdot\text{s})$$ Distractor Analysis: - Omitting the square root (using linear pressure difference) yields orders of magnitude error. - Inverting membrane thickness yields incorrect flux.

Find out where you actually stand

A free 20-question diagnostic across every FE Chemical knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Materials Science is where your time should go at all.

Start the free Chemical diagnostic

Retaking the FE Chemical exam?

Copy the scores from your NCEES diagnostic report and see whether Materials Science is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Chemical knowledge areas