ExamPass EngineeringExamPass Engineering Start free
FE Chemical · Knowledge area 7 of 17

Process Design on the FE Chemical exam

Process Design accounts for 8 of the 110 questions — 7.3% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions8
Share of exam7.3%
Rank by weight7/17
In our bank29

What Process Design covers

On the FE Chemical exam this area covers process flow diagrams, equipment sizing, piping and instrumentation, heat and mass integration, economic evaluation of designs, and optimisation.

What the questions look like: A sizing calculation for a vessel, pump or exchanger, or an economic comparison between two design options.

Worth knowing cold: These questions reward reading carefully. The computation is usually simple once you have identified which design basis the question fixes.

3 free Process Design practice problems

These come from our FE Chemical bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A horizontal cylindrical chemical process vessel is designed according to ASME Boiler and Pressure Vessel Code, Section VIII, Division 1. The vessel has an inside diameter of $D = 2.40\text{ m}$ (inside radius $R = 1200\text{ mm}$) and operates at an internal design pressure of $P = 2.50\text{ MPa}$. The construction material is SA-516 Grade 70 carbon steel plate with a maximum allowable stress of $S = 138\text{ MPa}$ at the design temperature. Welded longitudinal seams undergo $100\%$ full radiographic examination ($E = 1.00$). If a corrosion allowance of $CA = 3.00\text{ mm}$ is specified, the minimum required shell thickness is most nearly:

  1. A19.5 mm
  2. B22.0 mm
  3. C25.0 mmcorrect
  4. D28.5 mm
Show the solution

Step 1: Identify the ASME Section VIII Div 1 formula for cylindrical shell thickness under internal pressure: $$t = \dfrac{P R}{S E - 0.6 P} + CA$$ Step 2: Substitute the design parameters: $$P = 2.50\text{ MPa}$$ $$R = 1200\text{ mm}$$ $$S = 138\text{ MPa}$$ $$E = 1.00$$ $$CA = 3.00\text{ mm}$$ Step 3: Calculate the nominal pressure-bearing thickness: $$P R = 2.50 \times 1200 = 3000\text{ MPa}\cdot\text{mm}$$ $$S E - 0.6 P = 138(1.00) - 0.6(2.50) = 138 - 1.50 = 136.5\text{ MPa}$$ $$t_{nominal} = \dfrac{3000}{136.5} = 21.978\text{ mm}$$ Step 4: Add the specified corrosion allowance: $$t_{min} = t_{nominal} + CA = 21.978 + 3.00 = 24.978\text{ mm} \approx 25.0\text{ mm}$$ Distractor Analysis: - Option A (19.5 mm) uses diameter instead of radius or an inflated allowable stress. - Option B (22.0 mm) calculates the pressure-bearing thickness correctly ($21.98\text{ mm}$) but forgets to add the $3.00\text{ mm}$ corrosion allowance. - Option D (28.5 mm) assumes an uninspected welded joint efficiency ($E = 0.85$ or $0.70$) instead of the full radiography $E = 1.00$ specified.

Problem 2

A vertical vapor-liquid flash separator drum (V-201) equipped with a wire mesh demister pad processes a two-phase feed stream. The overhead vapor rate is $\dot{m}_v = 18,000\text{ kg/h} = 5.00\text{ kg/s}$ (vapor density $\rho_v = 4.00\text{ kg/m}^3$, liquid density $\rho_l = 600\text{ kg/m}^3$). In accordance with the Souders-Brown equation from the NCEES FE Reference Handbook ($v_{max} = K_{SB} \sqrt{(\rho_l - \rho_v)/\rho_v}$ with $K_{SB} = 0.107\text{ m/s}$), the vessel is sized for a design vapor velocity equal to $80.0\%$ of $v_{max}$. The minimum required inside diameter of the drum ($D$, in meters) is most nearly:

  1. A0.85 m
  2. B1.23 mcorrect
  3. C1.65 m
  4. D2.10 m
Show the solution

Step 1: Calculate the maximum allowable vapor velocity ($v_{max}$) from the Souders-Brown equation in the NCEES FE Reference Handbook: $$v_{max} = K_{SB} \sqrt{\frac{\rho_l - \rho_v}{\rho_v}}$$ $$\sqrt{\frac{\rho_l - \rho_v}{\rho_v}} = \sqrt{\frac{600 - 4.00}{4.00}} = \sqrt{\frac{596}{4.00}} = \sqrt{149.0} \approx 12.2065$$ $$v_{max} = (0.107\text{ m/s}) \times 12.2065 \approx 1.3061\text{ m/s}$$ Step 2: Calculate the design vapor velocity ($v_{design}$): $$v_{design} = 0.80 \times v_{max} = 0.80 \times 1.3061\text{ m/s} \approx 1.0449\text{ m/s}$$ Step 3: Calculate volumetric vapor flow rate ($Q_v$): $$Q_v = \frac{\dot{m}_v}{\rho_v} = \frac{5.00\text{ kg/s}}{4.00\text{ kg/m}^3} = 1.250\text{ m}^3/\text{s}$$ Step 4: Compute the minimum required drum cross-sectional area ($A$) and inside diameter ($D$): $$A = \frac{Q_v}{v_{design}} = \frac{1.250\text{ m}^3/\text{s}}{1.0449\text{ m/s}} \approx 1.1963\text{ m}^2$$ $$D = \sqrt{\frac{4 A}{\pi}} = \sqrt{\frac{4(1.1963\text{ m}^2)}{\pi}} = \sqrt{1.5232} \approx 1.234\text{ m} \approx 1.23\text{ m}$$ Distractor Analysis: - Option A (0.85 m): Uses 100% $v_{max}$ with square root error. - Option B (1.23 m): Correct. - Option C (1.65 m): Uses $K_{SB} = 0.06\text{ m/s}$ (undemisted drum). - Option D (2.10 m): Uses liquid volumetric flow rate.

Problem 3

An equal-percentage control valve has rangeability parameter $R = 50.0$ and a maximum design capacity of $Q_{max} = 120.0\text{ gpm}$. In accordance with the valve characteristic equation from the NCEES FE Reference Handbook ($Q/Q_{max} = R^{x - 1}$, where $x$ is fractional stem lift), the delivered volumetric flow rate ($Q$, in gpm) when the valve stem is at $70.0\%$ travel ($x = 0.700$) is most nearly:

  1. A17.0 gpm (14.1% of maximum)
  2. B37.1 gpm (30.9% of maximum)correct
  3. C58.4 gpm (48.7% of maximum)
  4. D84.0 gpm (70.0% of maximum)
Show the solution

Step 1: Identify the inherent equal-percentage flow characteristic relationship: $$\frac{Q}{Q_{max}} = R^{x - 1}$$ Given $R = 50.0$ and $x = 0.700$: $$x - 1 = 0.700 - 1.000 = -0.300$$ Step 2: Evaluate the fractional flow capacity: $$\frac{Q}{Q_{max}} = (50.0)^{-0.300} = \frac{1}{(50.0)^{0.300}}$$ $$(50.0)^{0.300} = e^{0.300 \ln(50.0)} = e^{0.300 \times 3.9120} = e^{1.1736} = 3.2337$$ $$\frac{Q}{Q_{max}} = \frac{1}{3.2337} = 0.30925$$ Step 3: Compute the actual volumetric flow rate ($Q$): $$Q = 0.30925 \times 120.0\text{ gpm} = 37.11\text{ gpm} = 37.1\text{ gpm}$$ Distractor Analysis: - Option A: Evaluates flow at 50% stem lift ($x = 0.50$, where $Q = 16.97\text{ gpm}$). - Option B: Correct. - Option C: Uses logarithmic mean between minimum and maximum flow. - Option D: Uses linear valve characteristic ($Q = 0.70 Q_{max} = 84.0\text{ gpm}$).

Find out where you actually stand

A free 20-question diagnostic across every FE Chemical knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Process Design is where your time should go at all.

Start the free Chemical diagnostic

Retaking the FE Chemical exam?

Copy the scores from your NCEES diagnostic report and see whether Process Design is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Chemical knowledge areas