ExamPass EngineeringExamPass Engineering Start free
FE Civil · Knowledge area 10 of 18

Dynamics on the FE Civil exam

Dynamics accounts for 5 of the 110 questions — 4.5% of your exam. It sits in the middle of the paper by weight: too big to skip, not big enough to dominate your plan.

Questions5
Share of exam4.5%
Rank by weight10/18
In our bank17

What Dynamics covers

On the FE Civil exam this area covers kinematics of particles and rigid bodies, projectile motion, Newton’s second law, work-energy and impulse-momentum methods, and curvilinear and rotational motion.

What the questions look like: A projectile range or height, an acceleration from a force balance, a velocity after an impact from conservation of momentum, or a car on a curve.

Worth knowing cold: Choose the method before the algebra: work-energy for problems linking speed and distance, impulse-momentum for problems linking speed and time.

3 free Dynamics practice problems

These come from our FE Civil bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A train starts from rest and accelerates at 2.0 m/s² for 5 seconds. It then decelerates at 1.5 m/s² until it comes to a complete stop. What is the total distance traveled?

  1. A25.00 m, counting only the accelerating phase
  2. B33.33 m, counting only the decelerating phase
  3. C83.33 m, adding an extra accelerating phase that the problem does not describe
  4. D58.33 mcorrect
Show the solution

Break the motion into its two phases and find the distance covered in each. Phase 1 (acceleration): v₁ = a₁t₁ = 2.0(5) = 10 m/s. d₁ = ½a₁t₁² = ½(2.0)(5)² = 25 m. Phase 2 (deceleration from 10 m/s to 0, at 1.5 m/s²): t₂ = v₁/a₂ = 10/1.5 = 6.667 s. d₂ = v₁t₂ − ½a₂t₂² = 10(6.667) − ½(1.5)(6.667)² = 66.67 − 33.33 = 33.33 m. Total distance = d₁ + d₂ = 25 + 33.33 = 58.33 m. Sanity check: Phase 2 covers more distance than Phase 1 (33.33 m vs. 25 m) even though both phases change speed by the same 10 m/s — this makes sense because the gentler deceleration (1.5 vs. 2.0 m/s²) takes longer to complete, and the train covers ground the whole time it's still moving.

Problem 2

Two vehicles collide and remain locked together afterward, moving off as a single mass. Which statements about this perfectly inelastic collision are correct? Select the two that apply.

  1. AThe total kinetic energy of the system is conserved through the collision
  2. BThe coefficient of restitution for the collision equals one
  3. CThe two bodies share a common velocity immediately after impact
  4. DThe total linear momentum of the system is conserved through the collision
Show the solution

Collisions are analyzed by separating what is always conserved from what is not, and that separation is the whole point of the exercise. LINEAR MOMENTUM IS CONSERVED in every collision regardless of type, because the impact forces are internal to the system and act in equal and opposite pairs — this is what makes the problem solvable at all, and it holds whether the bodies bounce apart or stick together. A COMMON FINAL VELOCITY is the defining feature of the perfectly inelastic case, and it is what reduces the two unknown final velocities to one, so momentum conservation alone determines the outcome. KINETIC ENERGY IS NOT CONSERVED: the perfectly inelastic collision dissipates the maximum energy any collision can, converting it into permanent deformation, heat and sound, which is precisely the principle a vehicle crumple zone is designed around. A COEFFICIENT OF RESTITUTION OF ONE describes the opposite extreme, a perfectly elastic collision where the bodies separate at the same relative speed they approached; the perfectly inelastic case has a restitution coefficient of zero, since the relative separation speed is nil.

Problem 3

A rope is wrapped around a 20 kg solid-disk hoist drum of radius 0.30 m that turns on a frictionless axle. A 5 kg bucket hangs from the rope and is released from rest. The speed of the bucket after it has fallen 2.0 m is most nearly:

  1. A2.80 m/s
  2. B3.62 m/scorrect
  3. C4.43 m/s
  4. D6.26 m/s
Show the solution

Step 1: Energy conservation: the bucket's loss of potential energy becomes the bucket's translational energy plus the drum's rotational energy. $$mgh = \tfrac{1}{2}mv^2 + \tfrac{1}{2}I\omega^2$$ Step 2: Solid disk: $I = \tfrac{1}{2}MR^2$, and the rope does not slip, so $\omega = v/R$: $$\tfrac{1}{2}I\omega^2 = \tfrac{1}{2}\left(\tfrac{1}{2}MR^2\right)\dfrac{v^2}{R^2} = \tfrac{1}{4}Mv^2$$ The radius cancels. Step 3: Substitute: $$5(9.81)(2.0) = \tfrac{1}{2}(5)v^2 + \tfrac{1}{4}(20)v^2 \implies 98.1 = 7.5v^2$$ Step 4: $v = \sqrt{98.1/7.5} = \sqrt{13.08} = 3.62$ m/s. Distractor Analysis: - Option A (2.80) models the drum as a thin ring, $I = MR^2$. - Option C (4.43) is free fall from 1.0 m, halving the height by mistake. - Option D (6.26) is free fall from 2.0 m, ignoring the drum's inertia.

Find out where you actually stand

A free 20-question diagnostic across every FE Civil knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Dynamics is where your time should go at all.

Start the free Civil diagnostic

Retaking the FE Civil exam?

Copy the scores from your NCEES diagnostic report and see whether Dynamics is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Civil knowledge areas

Dynamics on other FE exams

The same knowledge area is weighted differently on each exam, and the questions differ with it.