ExamPass EngineeringExamPass Engineering Start free
FE Civil · Knowledge area 16 of 18

Fluid Mechanics on the FE Civil exam

Fluid Mechanics accounts for 4 of the 110 questions — 3.6% of your exam. It is one of the lighter areas, which makes it a good place to secure quick marks rather than a place to spend weeks.

Questions4
Share of exam3.6%
Rank by weight16/18
In our bank14

What Fluid Mechanics covers

On the FE Civil exam this area covers fluid properties, hydrostatic pressure and forces on surfaces, buoyancy, the continuity and energy equations, the momentum equation, pipe friction and minor losses, and flow measurement.

What the questions look like: A pressure or force on a submerged surface, a head loss from the Darcy-Weisbach equation and a Moody-chart friction factor, or a velocity from Bernoulli.

Worth knowing cold: Check the Reynolds number before choosing a friction relationship. Laminar and turbulent answers differ by far more than rounding.

3 free Fluid Mechanics practice problems

These come from our FE Civil bank, written to the same specification as the exam. Try each one before opening the solution.

Problem 1

A venturi meter reduces a pipe from 300 mm to 150 mm diameter. A mercury manometer (specific gravity 13.6) connected across the throat registers a reading of 0.50 m, with water (specific gravity 1.0) as the flowing fluid. Neglecting losses, what is the flow rate through the pipe?

  1. A0.1965 m³/s, omitting the velocity-of-approach correction for the upstream area
  2. B0.0572 m³/s, using the raw manometer reading instead of the equivalent head of water
  3. C0.8117 m³/s, using the upstream pipe area instead of the throat area
  4. D0.2029 m³/scorrect
Show the solution

First convert the manometer reading to an equivalent head difference, then combine continuity and Bernoulli's equation. Head difference: Δh = R(SG manometer fluid /SG flowing fluid − 1) = 0.50(13.6/1.0 − 1) = 0.50(12.6) = 6.3 m. Continuity: A₁V₁ = A₂V₂, with area ratio A₂/A₁ = (150/300)² = 0.25, so V₁ = 0.25V₂. Bernoulli between the two sections: Δh = (V₂² − V₁²)/(2g) = V₂²(1 − 0.25²)/(2g). V₂² = 2gΔh/(1−0.0625) = 2(9.81)(6.3)/0.9375 = 123.6/0.9375 = 131.86 → V₂ = 11.48 m/s. Q = V₂A₂ = 11.48 × (π/4)(0.150)² = 11.48 × 0.01767 = 0.2029 m³/s. Sanity check: the mercury-over-water manometer multiplies a modest 0.5 m reading into a 6.3 m equivalent water head, which is why venturi meters can register strong, easily readable deflections even from fairly modest actual flows — exactly why mercury manometers were historically preferred for this kind of measurement.

Problem 2

A venturi meter has an inlet (throat approach) diameter of 0.30 m narrowing to a throat diameter of 0.15 m, installed in a horizontal water line. A pressure drop of 40 kPa is measured between the inlet and the throat. Using the venturi flow equation Q = A2*sqrt(2*deltaP/rho / (1-(A2/A1)^2)), what is the flow rate, in m^3/s? Round to 3 decimal places.

  1. A0.158 m³/s, omitting the velocity-of-approach correction for the area ratio
  2. B0.653 m³/s, using the inlet area instead of the throat area
  3. C0.082 m³/s, using half the measured pressure drop
  4. D0.163 m³/scorrect
Show the solution

A venturi meter infers flow rate from the pressure drop caused by the flow accelerating through a constriction, combining Bernoulli's equation (relating pressure and velocity) with continuity (relating the velocities at the two different cross-sections) into the single formula given. Areas: A1 = pi/4(0.30)^2 = 0.0707 m^2, A2 = pi/4(0.15)^2 = 0.01767 m^2. Area ratio: (A2/A1)^2 = (0.25)^2 = 0.0625 (since A2/A1 = (0.15/0.30)^2 = 0.25, from the diameter ratio squared for areas). Substituting into the flow equation: Q = 0.01767*sqrt(2(40,000)/1,000/(1-0.0625)) = 0.01767*sqrt(80/0.9375) = 0.01767*sqrt(85.33) = 0.01767(9.238) = 0.1632 m^3/s, which rounds to 0.163 m^3/s. The (1-(A2/A1)^2) term in the denominator corrects for the fact that the approach velocity at the inlet is not negligible, unlike a simple orifice discharging from a large reservoir.

Problem 3

A vertical rectangular sluice gate of width $b = 2.0\text{ m}$ and height $h = 3.0\text{ m}$ retains water (unit weight $\gamma = 9.81\text{ kN/m}^3$) on its upstream side. The top edge of the gate is submerged at a depth of $d = 2.0\text{ m}$ below the free water surface. What is the vertical distance from the water surface to the center of pressure $y_{cp}$ on the gate?

  1. A3.50 m
  2. B3.71 mcorrect
  3. C3.95 m
  4. D4.20 m
Show the solution

Step 1: Determine the vertical depth to the centroid of the rectangular gate $y_c$: $$y_c = d + \dfrac{h}{2} = 2.0\text{ m} + \dfrac{3.0\text{ m}}{2} = 2.0 + 1.5 = 3.50\text{ m}$$ Step 2: Calculate the area $A$ and centroidal second moment of area $I_c$ of the gate: $$A = b \times h = 2.0\text{ m} \times 3.0\text{ m} = 6.00\text{ m}^2$$ $$I_c = \dfrac{b h^3}{12} = \dfrac{(2.0\text{ m})(3.0\text{ m})^3}{12} = \dfrac{2.0 \times 27.0}{12} = 4.50\text{ m}^4$$ Step 3: Apply the FE Reference Handbook equation for the location of the center of pressure: $$y_{cp} = y_c + \dfrac{I_c}{y_c A}$$ Step 4: Compute $y_{cp}$: $$y_{cp} = 3.50 + \dfrac{4.50\text{ m}^4}{(3.50\text{ m})(6.00\text{ m}^2)} = 3.50 + \dfrac{4.50}{21.00} = 3.50 + 0.2143 = 3.714\text{ m} \approx 3.71\text{ m}$$ Distractor Analysis: - Option A (3.50 m) reports the depth of the centroid $y_c$, neglecting the hydrostatic pressure gradient eccentricity. - Option B is the correct center of pressure location. - Option C (3.95 m) uses $I = b h^3 / 3$ (moment of area about the base instead of the centroid). - Option D (4.20 m) evaluates $y_{cp}$ as $d + 2h/3$, which is only valid when the gate extends to the water surface.

Find out where you actually stand

A free 20-question diagnostic across every FE Civil knowledge area, scored in the real exam interface. You get a projected score and the areas costing you the most — so you know whether Fluid Mechanics is where your time should go at all.

Start the free Civil diagnostic

Retaking the FE Civil exam?

Copy the scores from your NCEES diagnostic report and see whether Fluid Mechanics is where your next attempt gains the most points, or whether another area deserves the time first.

Analyze my diagnostic report

Other FE Civil knowledge areas

Fluid Mechanics on other FE exams

The same knowledge area is weighted differently on each exam, and the questions differ with it.